325 In the case of non-fissile or fissile-excepted uranium hexafluoride, the material must be classified under UN 2978. The proper shipping name Paint related material, corrosive, flammable may be used for consignments of packages containing Paint, corrosive, flammable and Paint related material, corrosive, flammable in the same package; c. The proper shipping name Paint related material, flammable, corrosive may be used for consignments of packages containing Paint, flammable, corrosive and Paint related material, flammable, corrosive in the same package; and. Radiation detectors transported as individual components must be transported as follows: (1) They must be packed in a sealed intermediate plastic liner with sufficient absorbent or adsorbent material to absorb or adsorb the entire gas contents. 16 This description applies to smokeless powder and other solid propellants that are used as powder for small arms and have been classed as Division 1.3C, 1.4C and Division 4.1 in accordance with 173.56 of this subchapter. For transportation by aircraft, as an inner packaging of a combination packaging with a maximum gross mass of 30 kg when packaged as a limited quantity in accordance with 173.27(f). 15, 1976, unless otherwise noted. A51 For aircraft batteries, irrespective of the quantity limitations specified in Column (9A) of the 172.101 Table or 175.75(c), wet cell batteries, UN2794 or UN2795, up to a limit of 100 kg net mass per package may be transported aboard passenger aircraft. If you have comments or suggestions on how to improve the www.ecfr.gov website or have questions about using www.ecfr.gov, please choose the 'Website Feedback' button below. Dry sodium cyanide or potassium cyanide is also permitted in siftproof, water-resistant, fiberboard IBCs when transported in closed freight containers or transport vehicles. B57 Class 115A tank car tanks used to transport chloroprene must be equipped with a non-reclosing pressure relief device of a diameter not less than 305 mm (12 inches) with a maximum rupture disc pressure of 310 kPa (45 psig). Column 4 specifies the applicability of 178.275(g)(3) of this subchapter for the pressure relief devices. Ch 6.0b Flashcards | Quizlet 41 This material at the Packing Group II hazard criteria level may be transported in Large Packagings. Table 1. Nickel-metal hydride batteries subject to this special provision are subject only to the following requirements: (1) The batteries must be prepared and packaged for transport in a manner to prevent a dangerous evolution of heat, short circuits, and damage to terminals; and are subject to the incident reporting in accordance with 171.16 of this subchapter if a fire, violent rupture, explosion or dangerous evolution of heat (i.e., an amount of heat sufficient to be dangerous to packaging or personal safety to include charring of packaging, melting of packaging, scorching of packaging, or other evidence) occurs as a direct result of a nickel metal hydride battery; and (2) when loaded in a cargo transport unit in a total quantity of 100 kg gross mass or more, the shipping paper requirements of Subpart C of this part, the manifest requirements of 176.30 of this subchapter, and the vessel stowage requirements assigned to this entry in Column (10) of the 172.101 Hazardous Materials Table. A rocket motor to be considered nonpropulsive must be capable of unrestrained burning and must not appreciably move in any direction when ignited by any means. TP16 The portable tank must be protected against over and under pressurization which may be experienced during transportation. 181 When a package contains a combination of lithium batteries contained in equipment and lithium batteries packed with equipment, the following requirements apply: a. Energy storage capacity means the energy held by a capacitor, as calculated using the nominal voltage and capacitance. N11 This material is excepted for the specification packaging requirements of this subchapter if the material is packaged in strong, tight non-bulk packaging meeting the requirements of subparts A and B of part 173 of this subchapter. TP47 The 2.5 year internal examination may be waived or substituted by other test methods or inspection procedures specified by the competent authority or its authorized body, provided that the portable tank is dedicated to the transport of the organometallic substances to which this tank special provision is assigned. c. Primary receptacles may also be further packed in specification bulk outer packagings. 61 A chemical oxygen generator is spent if its means of ignition and all or a part of its chemical contents have been expended. When column 7 of the Hazardous Materials Table (49 CFR 172.101) includes a special provision code for an entry in the table, the requirement of that code - or codes, there may be several of them - is in addition to the general packaging requirements of 173.24 and any other applicable packaging requirements in Part 173. Lading must be blanketed at all times with a dry inert gas at a pressure not to exceed 103 kPa (15 psig). Lead compounds that have a solubility of 5% or less in accordance with this special provision are not subject to the requirements of this subchapter that pertain to Marine Pollutants. (v) The box must be constructed from high-density polyethylene in the density range 0.950-0.962, and be capable of holding liquid when in the upright position. Except as otherwise provided in this subchapter, these special provisions do not apply to UN portable tanks or IBCs: B1 If the material has a flash point at or above 38 C (100 F) and below 93 C (200 F), then the bulk packaging requirements of 173.241 of this subchapter are applicable. guide. A53 Refrigerating machines and refrigerating machine components are not subject to the requirements of this subchapter when containing less than 12 kg (26.4 pounds) of a non-flammable gas or when containing 12 L (3 gallons) or less of ammonia solution (UN2672) (see 173.307 of this subchapter). 62 Oxygen generators (see 171.8 of this subchapter) are not authorized for transportation under this entry. Amdt. A82 The quantity limits in columns (9A) and (9B) do not apply to human or animal body parts, whole organs or whole bodies known to contain or suspected of containing an infectious substance. 109 Rocket motors must be nonpropulsive in transportation unless approved in accordance with 173.56 of this subchapter. Subpart BTable of Hazardous Materials and Special Provisions 172.101 Purpose and use of haz-ardous materials table. Portable tank instructions T1 through T22 specify the applicable minimum test pressure, the minimum shell thickness (in reference steel), bottom opening requirements and pressure relief requirements. 332 Magnesium nitrate hexahydrate is not subject to the requirements of this subchapter. Symbols, if used, must be registered with the Associate Administrator. These special provisions are in addition to the standard packaging requirements. TP10 A lead lining, not less than 5 mm thick, which shall be tested annually, or another suitable lining material approved by the competent authority, is required. N76 For materials of not more than 25 percent active ingredient by weight, packages consisting of inner metal packagings not greater than 250 mL (8 ounces) capacity each, packed in strong outer packagings together with sufficient absorbent material to completely absorb the liquid contents are authorized and need not conform to the requirements of part 178 of this subchapter. 177 Gasoline, or, ethanol and gasoline mixtures, for use in internal combustion engines (e.g., in automobiles, stationary engines and other engines) must be assigned to Packing Group II regardless of variations in volatility. B116 The use of non specification, sift-proof dump or hopper type vehicles, and sift-proof roll-on/roll-off bulk bins, which must be covered by a tarpaulin, metal cover, or equivalent means is authorized for the transportation of spent bleaching earth by motor vehicle. For UN 3176, this requirement only applies when the hazardous material reacts dangerously with water. f. Flexible: 13H2, 13H3, 13H4, 13H5, 13L2, 13L3, 13L4, 13M1 and 13M2 (flexible IBCs must be sift-proof and water resistant or must be fitted with a sift-proof and water resistant liner). 337 Authorizes the use of regulated waste containers manufactured prior to October 1, 2006 to be marked with the alternative shipping name of Regulated medical waste, UN3291 and arrows that deviate as prescribed in 172.312(a)(2) in that they may be black or white. 146 This description may be used for a material that poses a hazard to the environment but does not meet the definition for a hazardous waste or a hazardous substance, as defined in 171.8 of this subchapter, or any hazard class, as defined in part 173 of this subchapter, if it is designated as environmentally hazardous by another Competent Authority. When a specific portable tank instruction is specified by a T Code in Column (7) of the 172.101 Table for a specific hazardous material, a specification portable tank conforming to an alternative tank instruction may be used if: (A) The alternative portable tank has a higher or equivalent test pressure (for example, 4 bar when 2.65 bar is specified); (B) The alternative portable tank has greater or equivalent wall thickness (for example, 10 mm when 6 mm is specified); (C) The alternative portable tank has a pressure relief device as specified in the T Code. They must be classified in accordance with the procedure as set out in the Manual of Tests and Criteria, part III, section 39 (IBR, see 171.7 of this subchapter). When a special provision specifies packaging or packaging requirements -, (1) The special provision is in addition to the standard requirements for all packagings prescribed in 173.24 of this subchapter and any other applicable packaging requirements in subparts A and B of part 173 of this subchapter; and. 386 When transported by private motor carrier only, the following corrosive liquids may be packaged in polyethylene bottles with a capacity no greater than 3.785 L (one gallon), further packed inside an open-top, heavy wall, high density polyethylene box (i.e., crate) in a manner that the polyethylene bottles are not subjected to any superimposed weight, and the boxes must be reasonably secured against shifting within the transport vehicle and loaded so as to minimize the possibility of coming in contact with other lading: Compounds, cleaning liquid, NA1760, PG II or III; Corrosive liquid, acidic, inorganic, n.o.s., UN3264, PG II; Corrosive liquid, acidic, organic, n.o.s., UN3265, PG III; Corrosive liquid, basic, inorganic, n.o.s., UN3266, PG II; Hydrochloric acid solution, UN1789, PG II; and. UN2258, 1,2-Propylenediamine: In HM-260B, PHMSA removed special provision A6 from column (7) of the . N80 Packages consisting of one inner metal can, not over 2.5 kg (5.5 pounds) capacity, packed in an outer wooden or fiberboard box, or a wooden barrel, are authorized and need not conform to the requirements of part 178 of this subchapter. The inlet to the venting device must be located in the vapor space of the IBC under maximum filling conditions. 102 The ends of the detonating cord must be tied fast so that the explosive cannot escape. Batteries and battery-powered device(s) containing batteries must be prepared and packaged for transport in a manner to prevent: (2) Short circuits, including but not limited to the following methods: (i) Packaging each battery or each battery-powered device when practicable, in fully enclosed inner packagings made of non-conductive material; (ii) Separating or packaging batteries in a manner to prevent contact with other batteries, devices or conductive materials (e.g., metal) in the packagings; or, (iii) Ensuring exposed terminals or connectors are protected with non-conductive caps, non-conductive tape, or by other appropriate means; and. (i) These provisions apply to the transportation of hazardous materials in IM and UN Specification portable tanks. Get the latest updates, news, and regulations for HazMat Transport and Waste Management. IBCs are only authorized if approved by the Associate Administrator. TP32 Portable tanks may be used subject to the following conditions: a. A hypochlorite solution, UN1791, is a Class 8 corrosive material. 430 This entry shall only be used for solid medical waste of Category A transported for disposal. B16 The lading must be completely covered with nitrogen, inert gas or other inert materials. FAR). d. The proper shipping name Printing ink related material may be used for consignments of packages containing Printing ink and Printing ink related material in the same package. Each tank must be equipped with pressure relief devices conforming to the following requirements: 1 Total venting capacity in standard cubic feet hour (S.C.F.H.) In addition, MC 312 and DOT 412 cargo tank motor vehicles must: c. Have a MAWP or design pressure of at least 87 psig; and. TP37 IM portable tanks are only authorized for the shipment of hydrogen peroxide solutions in water containing 72% or less hydrogen peroxide by weight. Interpretation Response | PHMSA - Pipeline and Hazardous Materials 166 When transported in non-friable tablet form, calcium hypochlorite, dry, may be transported as a Packing Group III material. c. The cylinders are collected and transported by a private or a contract carrier for reconditioning, reuse or disposal. B132 Except for transportation by aircraft, UN2813, Water reactive solid, n.o.s. 45 Temperature should be maintained between 18 C (64.4 F) and 40 C (104 F). 155 Fish meal, fish scrap and krill meal may not be transported if the temperature at the time of loading either exceeds 35 C (95 F), or exceeds 5 C (41 F) above the ambient temperature, whichever is higher. For transportation by aircraft, cargo transport units may only be offered for transportation and transported under conditions approved by the Associate Administrator. will bring you directly to the content. The Associate Administrator will base the authorization on results from Series 2 tests and a Series 6(c) test from the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) on packages as prepared for transport in accordance with the requirements of this subchapter. Primary receptacles must be further packed in non-specification bulk outer packagings such as cubic yard boxes, plastic rigid-wall bulk containers, dump trailers, and roll-off containers. The official, published CFR, is updated annually and available below under 169 This entry applies to lighter refills (see 171.8 of this subchapter) that contain a Division 2.1 (flammable) gas but do not contain an ignition device. Different Types of Solder- All Common Classifications 49 Mixtures of solids that are not subject to this subchapter and corrosive liquids may be transported under this entry without first applying the classification criteria of Class 8, provided there is no free liquid visible at the time the material is loaded or at the time the packaging or transport unit is closed. 11 The hazardous material must be packaged as either a liquid or a solid, as appropriate, depending on its physical form at 55 C (131 F) at atmospheric pressure. When a plus sign is assigned to mix- Note 1: Based on maximum lading pressure of 1 psig at top of cargo tank. 159 This material must be protected from direct sunshine and kept in a cool, well-ventilated place away from sources of heat. This entry does not apply to capacitors that by design maintain a terminal voltage (e.g., asymmetrical capacitors.). 140 This material is regulated only when it meets the defining criteria for a hazardous substance or a marine pollutant. Overcharge of the rechargeable lithium ion cells is precluded by design; iii. If appropriate, a package containing this material must conform to the additional labeling requirements of 172.402 of this subchapter. The identification number used must be consistent on package markings, shipping papers and emergency response information. d. Except for transportation by aircraft, neutron radiation detectors and radiation detection systems containing such detectors transported in accordance with paragraph a of this special provision are not subject to the labeling and placarding requirements of part 172 of this subchapter. When Column 7 refers to a special provision for a hazardous material, the meaning and requirements of that special provision are as set forth in 172.102 of this subpart. TP13 Self-contained breathing apparatus must be provided when this hazardous material is transported by sea. Wall thickness must be verified ultrasonically at intervals midway between periodic hydraulic tests (every 2.5 years). 176 This entry must be used for formaldehyde solutions containing methanol as a stabilizer. When Column 7 refers to a special provision for a hazardous material, the meaning and requirements of that special provision are as set forth in 172.102 of this subpart. Column 2 specifies the minimum test pressure, in bar (1 bar = 14.5 psig), at which the periodic hydrostatic testing required by 180.605 of this subchapter must be conducted. Use of these proper shipping names for domestic shipments may be made only under a DOT special permit, as defined in, and in accordance with the requirements of subpart B of part 107 of this subchapter. When transported by vessel, flexible, fiberboard or wooden IBCs must be sift-proof and water-resistant or be fitted with a sift-proof and water-resistant liner. TP17 Only inorganic non-combustible materials may be used for thermal insulation of the tank. 352 Ammonium chlorite, ammonium chlorite aqueous solutions, and mixtures of a chlorite with an ammonium salt are forbidden for transport. (2) They must be packed in strong outer packagings and the completed package must be capable of withstanding a 1.8 meter (5.9 feet) drop without leakage of gas contents from detectors. 347 Effective July 1, 2011, for transportation by aircraft, this entry may only be used if the results of Test series 6(d) of Part I of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) have demonstrated that any hazardous effects from accidental functioning are confined to within the package. formatting. B48 Portable tanks in sodium metal service may be visually inspected at least once every 5 years instead of being retested hydrostatically. N78 Packages consisting of inner glass, earthenware, or polyethylene or other nonfragile plastic bottles or jars not over 0.5 kg (1.1 pounds) capacity each, or metal cans not over five pounds capacity each, packed in outer wooden boxes, barrels or kegs, or fiberboard boxes are authorized and need not conform to the requirements of part 178 of this subchapter. B55 Water-tight, sift-proof, closed-top, metal-covered hopper cars, equipped with a venting arrangement (including flame arrestors) approved by the Associate Administrator are also authorized. 5 If this material meets the definition for a material poisonous by inhalation (see 171.8 of this subchapter), a shipping name must be selected which identifies the inhalation hazard, in Division 2.3 or Division 6.1, as appropriate. For all modes of transportation, a written report submitted, retained, and updated in accordance with 171.16 is required if a fire, violent rupture, explosion or dangerous evolution of heat occurs as a direct result of a dry battery or battery-powered device. d. Receptacles containing adsorbed or absorbed ammonia shall meet the following conditions: (1) Receptacles shall be made of a material compatible with ammonia as specified in ISO 11114-1:2012(E) and ISO 11114-1:2012/Amd 1:2017(E) (IBR, see 171.7 of this subchapter); (2) Receptacles and their means of closure shall be hermetically sealed and able to contain the generated ammonia; (3) Each receptacle shall be able to withstand the pressure generated at 85 C (185 F) with a volumetric expansion no greater than 0.1%; (4) Each receptacle shall be fitted with a device that allows for gas evacuation once pressure exceeds 15 bar (1500 kPa) without violent rupture, explosion or projection; and. 118 This substance may not be transported under the provisions of Division 4.1 unless specifically authorized by the Associate Administrator (see UN0143 or UN0150 as appropriate). A189 Except where the defining criteria of another class or division are met, concentrations of formaldehyde solution: a. Examples of equipment are lawnmowers, cleaning machines, or model boats and model aircraft. Tanks containing solidified methacrylic acid must not be reheated during transport. eCFR :: 49 CFR 172.101 -- Purpose and use of hazardous materials table. Each inner packaging contains not more than 30 mL; b. We recommend you directly contact the agency responsible for the content in question. 49 CFR 172.101 - Purpose and use of hazardous materials table. For non-pressurized lighters containing a Class 3 (flammable liquid) material, its design, description, and packaging must be approved by the Associate Administrator prior to being offered for transportation or transported in commerce. The Packing Group assigned will be II or III, according to the classification criteria for either Class 3 or Division 4.1, as appropriate, applied to the base material. These mixtures may be classified in Division 4.1 when tested in accordance with test series 6(c) of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) and approved by the Associate Administrator. per pound of hydrogen peroxide solution. These provisions apply only to transportation in IBCs and Large Packagings. When Column 7 refers to a special provision for a hazardous material, the meaning and requirements of that special provision are as set forth in 172.102 of this subpart. The lithium batteries must meet the requirements of 173.185(a) and contain the necessary systems to prevent overcharge and over discharge between the batteries. (1) Numeric provisions. It must not freeze at temperatures above 15 C (5 F). R1 A person who offers for transportation tank cars containing sulfur, molten or residue of sulfur, molten may reference the Sulfur Institute's, Molten Sulphur Rail Tank Car Guidance document (see 171.7 of this subchapter) to identify tank cars that may pose a risk in transportation due to the accumulation of formed, solid sulfur on the outside of the tank. (3) B codes. Interpretation Response | PHMSA - Pipeline and Hazardous Materials B131 When transported by highway, rail, or cargo vessel, waste Paint and Paint related material (UN1263; PG II and PG III), when in plastic or metal inner packagings of not more than 26.5 L (7 gallons), are excepted from the marking requirements in 172.301(a) and (c) and the labeling requirements in 172.400(a), when further packed in the following specification and non-specification bulk outer packagings and under the following conditions: a. 129 These materials may not be classified and transported unless authorized by the Associate Administrator on the basis of results from Series 2 Test and a Series 6(c) Test from the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) on packages as prepared for transport. However this examination is required when the conditions of 180.605(f) are met. The material is also be subject to operational controls which include not exceeding a temperature of 55C (130F) at the time it is offered or during transportation, not exceeding a transportation time of 24 hours, and drivers transporting spent bleaching earth must be trained in the properties and hazards of the spent bleaching earth. in such a manner as to prevent short circuits, accidental operation, and significant movement relative to the cargo transport unit under the shocks, loadings, and vibrations normally incident to transport. Non-specification bulk bins are authorized. PDF 171.26 49 CFR Ch. I (10-1-11 Edition) - GovInfo
Murders In Bowling Green, Ky, Mexican Cartel In Dominican Republic, Articles C